Compressor 2VM10-50/8: lower current and heat, higher oil pressure

Drive current dropped, the first stage became cooler, pressure in the lubrication system rose. 1 A — drive stator current, 16 → 15 A; 12 °C — stage I temperature, 149 → 137 °C; 10.3 % — oil pressure in the system, 3.9 → 4.3 atm (2004).

RUE “PA ‘Belaruskali’, 3rd Mine Group, sylvinite processing plant · approved by: chief engineer of Mine Group 3 I. L. Kozhich · report signed by the chief mechanical engineer, the chief engineer of the processing plant and the shop mechanics

Belarus · treatment 26.05–22.06.2004 · control measurement 18.06.2004 after 100 h of operation

PRODUCT“XADO technology”treatment on a running unit, without disassembly

TEST OBJECTCompressor 2VM10-50/8two compression stages · lubrication system · drive electric motor

DOCUMENT TYPETechnical report of the enterprise
with signatures and stamp

Key results

↓1A

drive stator current,16 → 15 A

↓12°C

stage I temperature,149 → 137 °C

↑10.3%

oil pressure in the system,3.9 → 4.3 atm

EQUIPMENT	CONDITION AT THE START OF TESTING	WHAT WAS MEASURED
Compressor 2VM10-50/8, processing plant of the 3rd Mine Group	Released from major overhaul on 20.05.2004; the “before” measurement was taken the same day	Vibration velocity and temperature of stages I and II, oil pressure, stator current of the drive

Compression stages — vibration and temperature

PARAMETER	BEFORE TREATMENT	AFTER 100 H
Vibration velocity, stage I	3.5 mm/s	3.04 mm/s
Vibration velocity, stage II	5.5 mm/s	5.04 mm/s
Stage I temperature	149 °C	137 °C
Stage II temperature	128 °C	134 °C

Vibration velocity — root-mean-square value in the 2 to 2000 Hz band; the measurement band is the same before and after treatment.

Lubrication system and drive electric motor

PARAMETER	BEFORE TREATMENT	AFTER 100 H
Oil pressure in the system	3.9 atm	4.3 atm
Oil temperature	52 °C	57 °C
Electric motor stator current	16 A	15 A

Oil pressure was measured in the compressor lubrication system, the current — at the stator of the drive electric motor.

Conclusion of the enterprise commission

The commission of RUE “PA ‘Belaruskali’, under the approval of the chief engineer of the 3rd Mine Group, recorded: 1. The effectiveness of ‘XADO technology’ in restoring worn parts without disassembling the equipment in regular operation has been demonstrated. 2. Recommended for the treatment of equipment within RUE ‘PA ‘Belaruskali’. The treatment was performed on a compressor that had just come out of a major overhaul — that is, on top of the condition delivered by standard repair — and even so, over 100 h of operation the drive current dropped, the first stage became cooler by 12 °C, and the pressure in the lubrication system rose to 4.3 atm. The unit was never once stopped for disassembly.

Current equivalent

Revitalizant gel for compressors and bearings →

Piston, screw and centrifugal compressors; rolling and sliding bearings running in an oil bath; machine-tool spindle units and slideways.

How such units are treated: Compressor

About this result: Vibration Power consumption

Method for this machine: Compressor 2ВМ10-50/8

Limits of this report: The results relate to the 2VM10-50/8 reciprocating compressor of the processing plant of the 3rd Mine Group of RUE “PA ‘Belaruskali’; on other equipment and operating modes the figures may differ.

Request a pilot for this unit

Compressor 2VM10-50/8: lower current and heat, higher oil pressure

Key results

Compression stages — vibration and temperature

Lubrication system and drive electric motor

Conclusion of the enterprise commission

Pilot treatment on the enterprise's equipment

Technology deployment programme

Compressor 2VM10-50/8: lower current and heat, higher oil pressure

Key results

Compression stages — vibration and temperature

Lubrication system and drive electric motor

Conclusion of the enterprise commission

Related cases